I had seen these beautiful ornaments just before Christmas 2020. Each one is so beautifully designed and detailed by Larissa Holland at mmmcrafts.blogspot.com and her patterns are for purchase in her etsy shop.

On Larissa’s website is the comprehensive list of supplies you will need to make your 12 Days Ornaments along with color guides and everything else you need to know. You’ll want to decide on your colors so you can order either one of the color bundles that Benzie Designs has of the beautiful wool felt or choose your own colors. You’ll also need the floss and the Notions Bundle. I’ll be honest. I did look around locally in combination with Amazon to see if I could get everything cheaper but nope. The notions bundle is a deal and don’t forget the fiberfill! You will also need one additional pack of the 8.5 x 11 printable Sulky Sticky Fabri-Solvy because 2 of the series have two pages of pieces you will need to print, for a total of 14 pages, and the packs only contain 12 pages.

I used cellophane envelopes and made a little kit for each ornament with the pattern pieces and notions needed to make each one as well as the color guide for each ornament from mmmcrafts. That way I could grab an ornament and my floss and work away. Larissa’s guides take you through each step in detail.

Then you’re ready to assemble the pieces into the adorable ornaments you see below!

Once you get all your supplies, it’s time to get everything organized and prepared. The first step is preparing your wool felt. You need to rinse each piece in warm water and then allow to dry. It will shrink a bit and you want to have that happen before you start cutting out your pattern pieces. You can hang to dry on a line or lay flat. I put some thick towels on our table and after gently squeezing out all the water from the sheet, I smoothed each one out and let dry over night on top of the towels.

While my felt was drying, I printed out all my patterns and put them in a three ring binder to keep them organized. Then I copied each sheet of the pattern pieces onto a sheet of the Sticky Fabri-Solvy. Once the felt was dry, I cut out the pieces for one ornament at a time, affixing the sticky fabri-solvy pieces to the colors I had chosen and cut them out.

Once the pieces have been embroidered, you rinse them under warm water to rinse away the Sticky Fabri-Solvy and let them dry.

This project was outside of my wheelhouse and not something I would normally choose to do but they were so exquisitely detailed and pretty, I just couldn’t resist and I’m so glad I didn’t! They patterns were written so well and so thoroughly that they were easy to follow and each ornament was just so fun to make! So much fun, I’m prepping another set!

Thanks for stopping by and have a great day!

Krista

#twelvedaysornaments #12daysornaments #mmmcrafts #benziedesign #benziefelt #dmcembroidery #dmcfloss #sulky

Getting Started

The first thing you want to do is to prepare your fabric. For this bag, my fabric measures 5-1/2 inches wide by 14 inches long. I’m using Kona Snow but you could use muslin or novelty fabrics or whatever you like. First, I like to go ahead a press approximately 1/4 inch in on each side to the wrong side of the fabric so I know where my seam is going and I know how much room I have to play around with applique, embroidery or whatever else I want to do.

Next, fold the top down 1/2 inch. Press and then fold down another 1/2 inch. Then fold in half, wrong sides together, and press your bottom seam.

Embellish Your Bag!

For this bag, I decided to do some applique. First, I cut out a 2-inch circle. I like to take just a tiny bit of invisible Elmer’s glue on my finger and apply it to a few spots on the back of the applique piece and then press with a hot iron. That way my shape stays in place while I stitch and I don’t have to mess with pins. Stitch around the edge. Note: Make sure your seam allowance is open and does not get caught in your stitching.

Next, I cut out a little heart and repeated the glue, pressing, and stitching.

I cut out strips to make an X. I did my glue and press with the first strip and then the second and then I stitched into place. Again, be sure your seam allowance is open and doesn’t get caught in your stitching!

Assemble Your Bag

Stitch up each side using 1/4″ seam allowance back stitching at the top and bottom. Stop approximately 1 inch below the bottom pressed seam line so your top tubes don’t get caught in your seam. Backstitch athe pressed top seam. Clip bottom corners.

Press side seams open. Press your top tube down again .

Finally, turn right side out. Stitch along the bottom edge of each top fold to create a tube in front and in back to place your ties.

Finish the Bag

Using a pin to secure the end of the ribbon or cord. Feed one end of your ribbon into the tube and out the other side and then into the second tube and out the other side so that your ends are both coming out of the same side of the bag. You are basically making a U with the ribbon, with both ends coming out on the same side.

Tie ends together. Repeat with cord or ribbon going the opposite direction.

Have Fun and Add Your Own Style

These are so great for party favors and valentines. You could use them in a table setting with personalized names and little gifts inside. You could also use them for Advent gifts and put numbers on the bags. Here is a fun little assortment using different fabrics and different ties (ribbon, cord, and twine).

Finally, I embroidered this bag with some cute hearts. This bag starting fabric measurement was 5 inches wide x 11 inches long. I used a water soluble marker to draw my hearts and 12 weight Sulky thread for the stitched hearts.

I hope you’ve enjoyed this tutorial. They really are quick and fun to make! I’m working on a dozen of the stitched heart bags right now!

Have a great day!

Krista

Shop Related Items